EXCEPTIONAL HIGH-GRADE ANTIMONY CONCENTRATE FROM MET-WORK
Released
Released
Announcement PDF
ASX: RMX
investorhub.redmountainmining.com.au info@redmountainmining.com.au Red Mountain Mining Ltd ACN 119 568 106
EXCEPTIONAL OAKY CREEK METALLURGY PRODUCES HIGH-
GRADE 51.8% ANTIMONY CONCENTRATE WITH 85% RECOVERY
HIGHLIGHTS:
• Geochemical and detailed mineralogical characterisation and a pilot crush, grind and flotation
study of a representative bulk sample of stibnite vein material from the high-grade Oaky
Creek Antimony prospect has produced a high-quality concentrate at 51.8%, well above the
30-40% commercial grade, that would be an excellent feed stock for pyrometallurgical
processing to produce a saleable Sb metal. The commercial concentrate produced a very high
85% antimony recovery
• The ~20kg sample was collected from shallow historical surface pits at Oaky Creek North and
is broadly representative of the orogenic antimony mineralisation exposed at surface at Oaky
Creek, the depth extent of which will be tested by the upcoming drilling program
• The bulk sample had a measured head grade 19.9% Sb and 0.25ppm Au, which is well within
the range of mineralised rock chip grab samples from the Oaky Creek prospect, which have
returned values of up to 39.3% Sb and 1.09ppm Au. Significantly, the sample returned a below
detection result of <0.01% As, suggesting that Arsenic is likely in very low concentrations at
Oaky Creek
• Mineralogically, TIMA analysis demonstrates that the sample is dominated by quartz (50.5%)
with stibnite (25.2%) the next most abundant phase. Oxidised stibnite and Sb (Fe)
oxyhydroxides collectively comprise 5.08%, with significant gangue phases including clays
(6.41%), ankerite-dolomite (3.04%), calcite (2.66%), feldspars (2.48%), Fe oxides and
hydroxides (2.02%), and chlorite (1.43%). Other sulfide and telluride phase are rare, totaling
only 0.05%
• Based on the mineralogy, a coarse (P80 = 212µm) crush was successfully trialed, with a total
flotation time of fourteen minutes producing a composite concentrate of 51.8% Sb at a 29.7%
mass pull, with an 85% recovery of the metal relative to head grade
• Five priority targets which will be tested at the upcoming drilling program at Oaky Creek
• Red Mountain advises that Due Diligence activities at the Pioneer Tungsten Project in the
United States are progressing well and on schedule, as part of the Company's option
agreement over the Pioneer Tungsten Project
ASX Announcement
25 May 2026
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
2
Red Mountain Mining Limited (ASX: RMX, US OTCQB: RMXFF, or “the Company”), a Critical
Minerals exploration and development company with an established portfolio in Tier-1 Mining Districts
in the United States and Australia, is pleased to announce the results of geochemistry, detailed
mineralogical characterisation and a pilot crush, grind and flotation study of a representative bulk
sample of quartz-stibnite-carbonate vein material from the high-grade Oaky Creek Antimony prospect
in the northern portion of the Company’s 100% owned Armidale Antimony-Gold project in the
Southern New England Orogen of New South Wales.
The ~20kg sample (Figure 1) was collected from shallow historical surface pits at Oaky Creek North
(Figure 2) and is broadly representative of the orogenic antimony mineralisation exposed at surface
at Oaky Creek, the depth extent of which will be tested by an RC drilling program that has been
recently approved by the NSW Regulator.
Figure 1: Examples of-mineralised material collected and submitted for metallurgical testing, with coarse grained silver-coloured stibnite
crystals clearly visible. (Refer ASX :RMX 16 February 2026 Metallurgical Testwork Commences at Oak Creek High Grade Antimony
Prospect)
Table 1: Metallurgical sample details (see Figure 1) and location Figure 6.
*Important Cautionary Statement: Visual estimates of mineral abundance should never be considered a proxy or substitute
for laboratory analyses where concentrations or grades are the factor of principal economic interest. Visual estimates also
potentially provide no information regarding impurities or deleterious physical properties relevant to valuations.
Sample_ID Easting Northing Datum Type Description %Carbonate %Quartz %Limonite %Stibnite %Stibiconti
Met01 266920 6659450 GDA94z56 OCN pit Multiple Stibnite veins in quartz-carbonate host 30 30 19.9 20 0.1
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
3
Figure 2: (A) Google Earth image showing auger soil sampling completed over the Oaky Creek antimony prospect relative to contoured
conventional soil antimony values and antimony minerallised (>0.5% Sb) rock chip samples. The two insets show the NSW 5m digital
elevation model 1over the (B) Oaky Creek North and (C) Oaky Creek South areas, showing auger antimony soil results, mapped quartz-
carbonate-stibnite vein traces and priority drill targets2. The bulk sample for metallurgical testing was collected from multiple shallow
historical pits at the Oaky Creek N workings3 (inset B).
1 ASX 2/2/26 Figure 2, Page 3 Expanded Exploration Programme Commences at Oaky Creek High-Grade Antimony Prospect
2
ASX: 30/3/26 Figure 4 Page 7 Exceptional Assays Define Multiple Antimony Drill Targets across Extensive Zone at Armidale Project
3
ASX: 30/3/26 Figure 2 Page 4 Exceptional Assays Define Multiple Antimony Drill Targets across Extensive Zone at Armidale Project
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
4
Analysis of the bulk sample was completed by ALS Metallurgy (Table 2) and returned a measured
head grade of 19.9% Sb and 0.25ppm Au, which is well within the range of mineralised rock chip
grab samples from the Oaky Creek prospect, which have returned values of up to 39.3% Sb and
1.09ppm Au1
. Significantly, the sample returned a below detection result of <0.01% As, suggesting
that this deleterious element is present in very low concentrations at Oaky Creek.
Table 2: Summary of assay results for the Oaky Creek North bulk metallurgical sample. (head assay from Auralia Metallurgical Report -
Fire Assay Au (LD 0.16ppm), Mixed Acid Digest/ICP finish for Ag (LD 1ppm) and XRF BM for all other elements (LD 0.01%))
Detailed mineralogy confirms that almost all antimony occurs in stibnite
A portion of the bulk sample was crushed and two size fractions (+212µm and -212µm) were
submitted for Tescan Integrated Mineral Analyzer (TIMA) analysis, while the head sample was
submitted for semi-quantitative X-ray diffraction (XRD) analysis. The XRD analysis of the head sample
indicated that 59% of the sample comprised quartz, with 21% stibnite (Sb2S3), 1% stibiconite
(Sb3O6(OH)) and <1% senarmontite (Sb2O3). Other significant gangue minerals included 10% clay
minerals and 7% carbonate. No other sulfide phases were detected by XRD.
The TIMA analytical results on the crushed samples are summarised in Table 3. As can be seen, quartz
is more abundant in the coarser (+212µm) fraction, while the other minerals are more concentrated
in the -212µm fraction. Overall, quartz (50.5%) is the dominant mineral phase in the sample with
stibnite (25.2%) the next most abundant phase. Oxidised stibnite and Sb (Fe) oxyhydroxides collectively
comprise 5.08%, with significant gangue phases including clays (6.41%), ankerite-dolomite (3.04%),
calcite (2.66%), feldspars (2.48%), Fe oxides and hydroxides (2.02%), and chlorite (1.43%). Other sulfide
1
RMX ASX Announcement 2 October 2025. https://investorhub.redmountainmining.com.au/announcements/7181513
Sb % 19.9
Au ppm 0.25
S % 7.02
SiO2 % 54.9
As % <0.01
Cu % <0.01
Fe % 1.92
MgO % 0.34
Pb % <0.01
Zn % <0.01
Ag ppm <1
Element Assay
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
5
and telluride phase are rare, totaling only 0.05%, which is consistent with the below detection limit
assay results for As, Cu, Pb and Zn (Table 2).
Table 3: Summary of assay results for the Oaky Creek North bulk metallurgical sample.
Flotation study delivers a high-quality saleable antimony concentrate
Flotation testing was undertaken at Auralia Metallurgy, who used their Basil Latino flotation machine
with a grind of P₈₀ = 212μm, a lead nitrate activator, potassium aryl xanthate (PAX) collecting agent
and a glycol ether based H57 frothing agent. These reagents are typically used for sulfide ores of this
type.
Five concentrates were produced from the flotation process, with individual flotation times varying
from 1 to 8 minutes and a total flotation time of fourteen minutes producing a composite concentrate
(Figure 3) of 51.8% Sb at a 29.7% mass pull, with an 85% recovery of the metal relative to the head
grade. The concentrate contained only 0.07ppm Au, with a much lower recovery of 32.8%, indicating
that this metal is likely to be locked in solid solution. Importantly, and consistent with the head grade,
+212 µm -212 µm Combined
Other sulphides/tellurides 0.02 0.06 0.05
Stibnite 16.0 27.5 25.2
Stibnite (O) 0.06 0.84 0.69
Sb(Fe) oxides/hydroxides 3.18 4.70 4.39
Feldspars 2.19 2.55 2.48
Quartz 62.5 47.4 50.5
Clays and similar 5.42 6.67 6.41
Micas 0.71 0.58 0.61
Chlorite 1.21 1.49 1.43
Amphibole/pyroxene 0.13 0.07 0.08
Other silicates 0.06 0.04 0.05
Phosphates 0.05 0.07 0.06
Calcite 2.96 2.58 2.66
Ankerite-dolomite 3.75 2.86 3.04
Fe-oxides/hydroxides 1.45 2.16 2.02
Scheelite 0.20 0.22 0.22
Other oxides 0.03 0.05 0.04
Sulphates 0.00 0.00 0.00
Others 0.05 0.12 0.10
TOTAL 100 100 100
Weight dist.% 20.4 79.7 100
Mineral group
Sb Comp
Mass% in fraction
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
6
the concentrate contained only 197ppm As, which is a low concentration of this deleterious element.
The concentrate would be an excellent feed stock for pyrometallurgical processing to produce a
saleable Sb metal, highlighting the potential quality of the antimony mineralisation at Oaky Creek, if
a sufficient resource is defined by Red Mountain’s planned drilling program.
Figure 3: Composite concentrate recovered by flotation, which assayed 51.8% Sb with a 29.7% mass pull and an 85% recovery from an
assayed head grade of 19.9% Sb. (Photo taken by RMX’s independent consulting metallurgist Rob Riggir)
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
7
Oaky Creek represents a significant 3km long orogenic antimony system with multiple
drill ready targets
The Oaky Creek prospect features quartz-carbonate-stibnite veins and breccias hosted within a tightly
folded and faulted sequence of metamorphosed Carboniferous mudstone, siltstone and fine
sandstone. The mineralisation has been targeted by two groups of shallow historical pits and shafts
at Oaky Creek North and Oaky Creek South.
The Company’s initial sampling program at Oaky Creek comprised a 50m x 100m spaced grid soil
sampling program centered on a major splay of the Namoi Fault, accompanied by rock chip sampling.
As initially reported in June 20252
, the soil sampling defines a coherent, ~1.5km long, 100-200m wide,
NNW-trending >2ppm Sb in soil anomaly extending both north and south of the historical workings
at Oaky Creek North and a similarly-oriented ~1km long >2ppm Sb in soil anomaly extending north
from the Oaky Creek South workings.
Sampling campaigns at Oaky Creek34
, returned multiple rock chip samples5, 6, 7
with values of over
25% Sb and 0.1g.t Au for five different areas, with mineralised and anomalous rock samples showing
a strong spatial correlation to the antimony soil anomaly (Figure 2). When considered collectively, the
soil and rock chip results indicate a significant orogenic antimony mineral system with a strike extent
of 3km, which is analogous to Larvotto Resources’ (ASX: LRV; Market Cap. ~AU$610 million)
Hillgrove Project, which lies east of Red Mountain’s project area.
Red Mountain’s ~1300 sample infill hand auger soil sampling campaign across the full ~3km strike
extent of the Oaky Creek prospect was completed across the past two quarters to tighten the
Company’s existing 100m x 50m spaced soil grid in order to better constrain individual high priority
drill targets. This detailed systematic work has allowed the company to define five high priority
orogenic antimony targets8
for drill testing at Oaky Creek (Figure 2) during the second quarter of
2026.
2
RMX ASX Announcement 7 June 2025. https://investorhub.redmountainmining.com.au/announcements/6998482
3
RMX ASX Announcement 27 June 2025. https://investorhub.redmountainmining.com.au/announcements/7026204
4RMX ASX Announcement 11 July 2025. https://investorhub.redmountainmining.com.au/announcements/7050680
5
RMX ASX Announcement 2 October 2025. https://investorhub.redmountainmining.com.au/announcements/7181513
6
RMX ASX Announcement 15 January 2026. https://investorhub.redmountainmining.com.au/announcements/7325282
7
RMX ASX Announcement 12 March 2026. https://investorhub.redmountainmining.com.au/announcements/7435807
8
RMX ASX Announcement 30 March 2026. https://investorhub.redmountainmining.com.au/announcements/7467812
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
8
Red Mountain Armidale Antimony-Gold Project background
Red Mountain’s 100%-owned Armidale Antimony-Gold Project lies in the Southern New England
Orogen (SNEO) in northeastern New South Wales, approximately west of Australia’s largest known
antimony deposit, Larvotto’s (ASX: LRV) Hillgrove deposit, which is also the 8th
largest antimony
deposit globally. The SNEO is recognised as Australia’s premier Antimony province (Figure 4).
Antimony occurs in hydrothermal quartz veins, breccias and stockworks, often with associated gold
and/or tungsten mineralisation.
Figure 4: Location of LRV’s Hillgrove Mine and other Known NSW gold and antimony mineral occurrences relative to Red Mountain’s
Armidale Antimony-Gold Project and NSW basement orogenic units. The map clearly demonstrates the prospectivity of the New England
Orogen for antimony and gold. The location the Peel Fault is also shown. (ASX :RMX 23 October 2025 – Armidale Antimony Project
Advances with Multiple Exceptional Prospects)
Red Mountain’s Armidale Antimony-Gold Project has an extensive 85km length along the western
side of the Peel Fault. The geology of the project area is dominated by isoclinally folded Carboniferous
metasediments of the Tamworth Belt, which is a forearc basinal package related to west-dipping
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
9
subduction of oceanic crust beneath the Lachlan Orogen. Ultramafic mélanges of the Great
Serpentinite Belt, which outcrop along the Peel Fault, are considered to be remnants of this oceanic
crust. The Peel Fault System has recognised world-class mineral potential, with over 400 known
orogenic gold and base metal mineral occurrences along its over 400km strike extent, but is
underexplored, with less than 200 mostly shallow drillholes over its length, the majority of which are
focused on discrete prospects.
Oaky Creek is the company’s highest priority and most advanced prospect within the project and is
one of several known orogenic gold and antimony occurrences within the tenement (Figure 5).
Figure 5: Geological Survey of NSW total magnetic intensity reduced to pole (TMI RTP) imagery and location of gold and antimony mineral
occurrences within and near to EL9732, summarising highlights of RMX’s exploration to date and the location of the Company’s Oaky Creek
and East Hills antimony prospects, Horsley Station gold prospect and Horsley North magnetic target. The mapped location of the Peel Fault
is also shown. (ASX:RMX 27/11/25 Figure 8, page 12 HIGH-GRADE ANTIMONY RESULTS AT ARMIDALE CONFIRM POTENTIAL FOR A MAJOR
ANTIMONY-GOLD SYSTEM)
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
10
Authorised for and on behalf of the Board,
Mauro Piccini
Company Secretary
Disclaimer
In relying on the above mentioned ASX announcement and pursuant to ASX Listing Rule 5.23.2, the Company confirms that
it is not aware of any new information or data that materially affects the information included in the above-mentioned
announcement.
Forward–Looking Statements
Some of the statements appearing in this announcement may be in the nature of forward-looking statements. You should
be aware that such statements are only predictions and are subject to inherent risks and uncertainties. Those risks and
uncertainties include factors and risks specific to the industries in which Red Mountain operates and proposes to operate
as well as general economic conditions, prevailing exchange rates and interest rates and conditions in the financial markets,
among other things. Actual events or results may differ materially from the events or results expressed or implied in any
forward- looking statement. No forward-looking statement is a guarantee or representation as to future performance or any
other future matters, which will be influenced by a number of factors and subject to various uncertainties and contingencies,
many of which will be outside Red Mountain’s control.
About Red Mountain Mining
Red Mountain Mining Ltd (ASX: RMX, US CODE: RMXFF) is a Critical Minerals and Gold exploration and development
company focussed on accelerating its United States and Australia based Projects, located in Tier-1 Mining Districts.
Red Mountain is fast-tracking its Critical Minerals projects in the US and Australia, and the Board and Management is
determined to rapidly define a portfolio of advanced projects to assist the United States and other Western countries with
a reliable, high-quality source of commodity supply, including from the Company’s Armidale Antimony-Gold Project located
in NSW, Australia, which has delivered multiple high-grade antimony rock chip samples to date (up to 39.3% Sb); and its US
Critical Minerals Portfolio. comprising the Pioneer Tungsten Project in Beaverhead County Montana, which encompasses
the same geology and exhibits the same skarn-style mineralisation as the 6.8Mt Gentung tungsten resource (owned by
NASDAQ: ALM); the Utah Antimony Project in the highly prospective Antimony Mining District of Utah, adjacent to the
Antimony Canyon Project (owned by ASX: AT4); the Thompson Falls Antimony Project with initial assay results of up to
36.5% Sb at historical mines located near the NYSE: UAMY Antimony Smelter, and two Idaho Antimony Projects.
Competent Person Statement
The information in this announcement that relates to Exploration Results and other technical information complies with the
2012 Edition of the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code).
It has been compiled and assessed under the supervision of contract geologist Mark Mitchell. Mr Mitchell is a Member of
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
11
the Australasian Institute of Geoscientists and has sufficient experience that is relevant to the style of mineralisation and
type of deposit under consideration and to the activity being undertaken to qualify as a Competent Person as defined in
the 2012 Edition of the JORC Code. Mr Mitchell consents to the inclusion in this announcement of the matters based on
his information in the form and context in which it appears.
JOIN THE RED MOUNTAIN MINING INVESTOR HUB
Visit https://investorhub.redmountainmining.com.au for access to the Investor Hub
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
12
Metallurgical sampling details
*Met01
Figure 6: Location of the metallurgical sample MET01 relative to the antimony rock chip and soil results for the Oaky Creek prospect, with
peak rock chip values for antimony and gold listed for the five main mineralised areas. The samples submitted for metallurgical testing
were collected from small historical pits at the Oaky Creek N Workings, which have returned rock chip sample assay results of up to 36.3%
Sb.
Met01
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
13
JORC Code, 2012 Edition - Table 1
1.1 Section 1 Sampling Techniques and Data
Criteria JORC Code explanation Commentary
Sampling
techniques
• Nature and quality of sampling (e.g. cut
channels, random chips, or specific
specialised industry standard
measurement tools appropriate to the
minerals under investigation, such as
down hole gamma sondes, or handheld
XRF instruments, etc). These examples
should not be taken as limiting the
broad meaning of sampling.
• Include reference to measures taken to
ensure sample representivity and the
appropriate calibration of any
measurement tools or systems used.
• Aspects of the determination of
mineralisation that are Material to the
Public Report.
• In cases where ‘industry standard’ work
has been done this would be relatively
simple (eg ‘reverse circulation drilling
was used to obtain 1 m samples from
which 3 kg was pulverised to produce a
30 g charge for fire assay’). In other
cases more explanation may be required,
such as where there is coarse gold that
has inherent sampling problems. Unusual
commodities or mineralisation types (eg
submarine nodules) may warrant
disclosure of detailed information.
• Metallurgical rock sample consisted of
~20kg of outcrop samples collected
from the Oaky Creek North Pits.
• The Rock chip samples was selective
based on visual identification of
Stibnite, the dominate antimony
mineral for metallurgical testing.
• The metallurgical Rock Sample was
sent to Auralia Metallurgy (Perth) for
ore characterisation, crushing, grinding
and floatation testing.
• The sample was biased towards
stibnite for metallurgical testing and is
not considered representative of the
mineralisation given it was one sample.
Drilling
techniques
• Drill type (e.g. core, reverse circulation,
open-hole hammer, rotary air blast,
auger, Bangka, sonic, etc) and details
(e.g. core diameter, triple or standard
tube, depth of diamond tails, face-
sampling bit or other type, whether core
is oriented and if so, by what method,
• No drilling reported
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
14
Criteria JORC Code explanation Commentary
etc).
Drill
sample
recovery
• Method of recording and assessing core
and chip sample recoveries and results
assessed.
• Measures taken to maximise sample
recovery and ensure representative
nature of the samples.
• Whether a relationship exists between
sample recovery and grade and whether
sample bias may have occurred due to
preferential loss/gain of fine/coarse
material.
• No drilling reported.
Logging • Whether core and chip samples have
been geologically and geotechnically
logged to a level of detail to support
appropriate Mineral Resource estimation,
mining studies and metallurgical studies.
• Whether logging is qualitative or
quantitative in nature. Core (or costean,
channel, etc) photography.
• The total length and percentage of the
relevant intersections logged.
• No drilling reported.
.
Sub-
sampling
techniques
and
sample
preparation
• If core, whether cut or sawn and whether
quarter, half or all core taken.
• If non-core, whether riffled, tube
sampled, rotary split, etc and whether
sampled wet or dry.
• For all sample types, the nature, quality
and appropriateness of the sample
preparation technique.
• Quality control procedures adopted for
all sub-sampling stages to maximise
representivity of samples.
• Measures taken to ensure that the
sampling is representative of the in situ
material collected, including for instance
results for field duplicate/second-half
sampling.
• Whether sample sizes are appropriate to
• Rock chip sampling is biased towards
outcrop that contained visually
identified stibnite at the Oaky Creek
North old workings.
• The bench testing required a
minimum of 18kg of ore for testing
through multiple streams of grid size
and floatation methods.
• The sample was crushed to two size
fractions (+212μm and -212μm) for
analysis by TIMA and semi-
quantitative XRD methods and
geochemical analysis (FA, ICPMS and
XRF BM) techniques.
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
15
Criteria JORC Code explanation Commentary
the grain size of the material being
sampled.
Quality of
assay data
and
laboratory
tests
• The nature, quality and appropriateness
of the assaying and laboratory
procedures used and whether the
technique is considered partial or total.
• For geophysical tools, spectrometers,
handheld XRF instruments, etc, the
parameters used in determining the
analysis including instrument make and
model, reading times, calibrations factors
applied and their derivation, etc.
• Nature of quality control procedures
adopted (e.g. standards, blanks,
duplicates, external laboratory checks)
and whether acceptable levels of
accuracy (i.e. lack of bias) and precision
have been established.
• The mineralised lode material was
characterised by XRD and TIMA through 2
size fractions.
• Planned sample preparation includes crush
to -3.35mm, blending, and split into 1kg
charges. 1kg Grids for P80 – 150 with head
assays determined for Sb, Au, Cu, Pb, Zn,
Fe, As, S, Sio2, MgO and Ag. Floatation
included 5 tests of 1kg batch Rougher,
Batch cleaner with regrind and continued
assays (XRF) through all steps.
• Assays were conducted by Fire Assay for
Au, Mixed Acid Digest and ICP-MS finish
for Ag and XRF BM for all other elements.
• Assay work including XRD and TIMA was
conducted at ALS Global laboratories in
Perth
• ALS is a NATA accredited Laboratory and
was responsible for all instrument
calibrations. No standards or blanks were
submitted by RMX as this QAQC is not
applicable to Metallurgical bench testing.
The Lab uses its own QAQC techniques to
comply with its NATA licence.
Verification
of
sampling
and
assaying
• The verification of significant
intersections by either independent or
alternative company personnel.
• The use of twinned holes.
• Documentation of primary data, data
entry procedures, data verification, data
storage (physical and electronic)
protocols.
• No drill holes reported.
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
16
Criteria JORC Code explanation Commentary
• Discuss any adjustment to assay data.
Location of
data points
• Accuracy and quality of surveys used to
locate drill holes (collar and down-hole
surveys), trenches, mine workings and
other locations used in Mineral Resource
estimation.
• Specification of the grid system used.
• Quality and adequacy of topographic
control.
• Met sample taken with GPS readings with
site locations recorded in GDA94 (z56).
• No mineral resource estimation is being
conducted.
Data
spacing
and
distribution
• Data spacing for reporting of Exploration
Results.
• Whether the data spacing and
distribution is sufficient to establish the
degree of geological and grade
continuity appropriate for the Mineral
Resource and Ore Reserve estimation
procedure(s) and classifications applied.
• Whether sample compositing has been
applied.
• First pass metallurgical sample testing to
develop flow sheet. Further testing of
mineralisation will be done along strike
once drilling programme is complete, to
check for grade continuity and check for
metallurgical consistency.
Orientation
of data in
relation to
geological
structure
• Whether the orientation of sampling
achieves unbiased sampling of possible
structures and the extent to which this is
known, considering the deposit type.
• If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to
have introduced a sampling bias, this
should be assessed and reported if
material.
• Aim of the first pass metallurgy is to
develop a flow sheet towards a commercial
Sb grade concentrate of 30-40%.
• No drilling conducted.
Sample
security
• The measures taken to ensure sample
security.
• Stibnite samples collected by staff and
shipped to Perth by air and directly handed
across to the laboratory. .
RED MOUNTAIN MINING LTD ASX: RMX INVESTORHUB.REDMOUNTAINMINING.COM.AU
17
Criteria JORC Code explanation Commentary
Audits or
reviews
• The results of any audits or reviews of
sampling techniques and data.
• No audit or reviews were conducted.
1.2 Section 2 Reporting of Exploration Results
(Criteria listed in the preceding section also apply to this section.)
Criteria JORC Code explanation Commentary
Mineral
tenement and
land tenure
status
• Type, reference name/number, location
and ownership including agreements or
material issues with third parties such
as joint ventures, partnerships,
overriding royalties, native title
interests, historical sites, wilderness or
national park and environmental
settings.
• The security of the tenure held at the
time of reporting along with any known
impediments to obtaining a licence to
operate in the area.
• The Exploration licence EL9732 is granted
and 100% wholly owned by Red Mountain
Mining and covers 391km2
.
• The licence is in its second year of grant
and has no identified conflicts
environmentally or with. Native with the
relevant claimant holders. The licence
covers freehold land with Land Access
agreement struck with local owners using
standard AMEC terms.
Exploration
done by other
parties
• Acknowledgment and appraisal of
exploration by other parties.
• The north-south elongate corridor covered
by the project contains no historical
mineral exploration drilling and has seen
limited previous surface exploration for
Antimony and Gold mineralisation. No soil
sampling for these elements had been
undertaken and rock chip and stream
sediment coverage is limited, leaving the
majority of the tenement untested by
systematic exploration and therefore is
considered having significant potential for
discovery. A number of historical
prospector workings (100 yrs. plus) for
antimony and gold have been reported
within the licence
Geology • Deposit type, geological setting and
style of mineralisation.
• The project is located in the Southern
New England Orogen. The geology of the
tenement is dominated by isoclinally
folded Carboniferous metasediments of
RED MOUNT
Share your feedback
Discover